Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the au- thor. Page 4 Features Setup Page You can install any one of these processors on the mainboard. The mainboard supports front-side bus speeds of MHz. Page Installing The Mainboard In A Case Refer to the following illustration and instructions for installing the mainboard in a case: This illustration shows an ex- 2. Secure the mainboard with ample of a mainboard being screws where appropriate.
|Published (Last):||24 March 2019|
|PDF File Size:||8.93 Mb|
|ePub File Size:||7.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
Other names used in this publication may be trademarks and are acknowledged. We will test more DDR modules in the future. I Chapter You can install any one of these processors on the mainboard. Take the following precautions when unpacking the mainboard and installing it in a system. Keep the mainboard and other components in their original static-proof packaging until you are ready to install them.
Page Chapter 2 2: Mainboard Installation Chapter 2 Mainboard Installation To install this mainboard in a system, follow the procedures in this chapter: Identify the mainboard components Install a CPU Install one or more system memory modules Verify that any jumpers or switches are set correctly Install the mainboard in a system chassis case Connect any extension brackets or cables to the mainboard connector headers Note: Any jumper on your mainboard that do not appear in the illustration above is for testing only.
Match the Pin-1 corners and insert the processor into the socket. No force is required and the processor should drop into place freely. Swing the locking lever down and hook it under the catch on the side of the socket. Page 15 2: Mainboard Installation To install a module, push the retaining latches at either end of the socket outwards.
Position the memory module correctly and insert it into the DIMM socket. Press the module down into the socket so that the retaining latches rotate up and secure the module in place by fitting into notches on the edge of the module. The jumper caps change the way the mainboard operates by changing the electronic circuits on the mainboard. If a jumper cap is removed from two pins, the pins are OPEN. You may need to clear the CMOS memory if the settings in the Setup Utility are incorrect and prevent your mainboard from operating.
You can install this mainboard in an ATX case. Install them by following the steps below. Note: All the ribbon cables used on the extension brackets have a red stripe on the Pin-1 side of the cable. Drives can be 3. On the mainboard, locate the two 4-pin connectors CD1 and CD2. There are two kinds of connector because different brands of CD- ROM drive have different kinds of audio cable connectors. Your computer uses this information to initialize all the components when booting up and functions as the basis for coordination between system components.
When you see this message, press the Delete key and the Main menu page of the Setup Utility appears on your monitor. If you press the F3 key, the system will automatically detect and configure the hard disks on the IDE channels. Take some care with this page. Making changes can affect the operation of your computer.
Floppy Drive If you enable this item, your system will check all Seek floppy disk drives at start up. If you press Y, and then Enter, the Setup Utility loads a set of fail-safe default values. These default values are not very demanding and they should allow your system to function with most kinds of hardware and memory chips. Under Normal, the resources are allocated to the onboard serial port.
The system will automatically detect the kind of CPU that you have installed and make the appropriate adjustments to the items on this page.
At the next dialog box, type in the new password, or just press Enter to disable password protection. Exit Highlight this item and press Enter to save the changes that you have made in the Setup Utility configuration and exit the program. Page Chapter 4 4: Software Chapter 4 Software Introduction The support softwar e CD-ROM that is included in the mainboard package contains all the drivers and utility programs needed to properly run the bundled products.
Below you can find a brief description of each software program, and the location for your mainboard version. TXT or something similar. This file may contain important information to help you install the software correctly. Click the Next button to run Auto Setup program. Check the box next to the items you want to install. The default options are recommended. Click the Next button to run the Installation Wizard.
You will need to follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete installing whatever software you selected to install: When the process is finished, all the support drivers and software will be installed and working.
EXE to install the application software.
ECS K7S5A User Manual
ECS K7S5A Manual
ECS K7S5A Pro User Manual